Your walls are the foundation of your home. The weather out there will not be nice and you need to pay special attention to the exterior walls of your house. It is not enough to paint your wall. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will begin peeling off.

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

“The outer part of your home’s wall is usually covered with a lot of dust and dirt that sticks to it. To ensure the efficiency of the process, you need to clear off the debris and dust thoroughly. The dirt and debris can be cleaned with a broom, brush or scraper. You can finish it off with a power washer.”

Step 3: Check out for the cracks and fill them up

Cracks and holes can develop over time on your walls. Follow up the cleaning process with a thorough finding of all the cracks and holes on the wall to ensure proper weatherproofing. Simply fill them with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The cement mixture can penetrate inside the cracks. Make sure you remove the loose cement from the wall before applying the cement.

Step 4: Add a layer of cement waterproofing sealer

If you want to make sure your wall is waterproof, you need to apply cement. After applying the cement in the crevices, let it dry and then apply the waterproof paint on the exterior walls. Let it become dry after that.

Step 5: Pick the right water-proofer

There are many waterproof products in the market. You have to pick the one that goes with the wall you have. The water-proofer should be chosen based on whether the wall is concrete or silicate.

It is possible to choose between a silicate-based concrete sealer and a concrete waterproofing coating. Pick a plaster waterproof Additive that will add strength to the walls.

Step 6: Apply the water-proofer

Use a roller or brush to apply the water-proofer. Give a thin coat if you want to apply more than one layer. Add the second coating after the first has dried.

Step 7: Apply tar and heavy-duty membrane

If you want to add more strength to the layer, you need to use a tar-based pitch after the drying of the cement. You can apply it on your wall.

After that, you need to apply a heavy-duty plastic or rubber membrane, which will ensure the proper care of your wall.

Step 8: Consider adding gravel

To lay the drainage pipes, you need a proper base beneath the footer. The drainage pipes will get adequate support from a 34 inch gravel base. Gravel is long- lasting and provides enhanced protection.

You need to lay the drainage pipe-cover with gravel. If you want to back-fill the gravel, level it near the footer. A covering for the pipe should be at least 3-inches.

Step 9: Add a fabric barrier

The fabric barrier should be secured with the perforated pipe. Ensuring a fabric barrier is the best way to prevent dirt from forming. Then back-fill the trench and build the top of the dirt relatively high and let it settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia is


Good waterproof gives your home a new life and strength to deal with outside weather issues. Magicrete can help you find good waterproof solutions for your walls. At a very low and affordable price, Magicrete can provide you with proper weatherproofing.

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like”

By Imran

Leave a Reply

Your email address will not be published. Required fields are marked *